Honing and PEEK: how the two fit together
Honing is an abrasive finishing process that uses expanding stones to correct bore geometry. It is used for holding roundness, straightness and a controlled surface pattern in a bore. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, robotics is used as the example: repeatability across a family of near identical parts.
How the two fit together
Honing and PEEK are specified together more often than separately. Honing is an abrasive finishing process that uses expanding stones to correct bore geometry, while PEEK is a high performance thermoplastic that holds its properties at temperature and resists chemicals; one produces the result and the other controls or finishes it.
Sequence
The order matters. Work is done with Honing, and then PEEK is applied to it; reversing the order is the usual cause of a part that measures correctly but does not work.
What to specify
| Specification | Typical value |
|---|---|
| Aspect | Note |
| This entry | Honing – IT6 |
| Related entry | PEEK – ±0.05 mm, because of thermal expansion |
| Material | 4140 alloy steel |
| Finish | Ra 0.2 µm with a plateau finish |
| Documentation | in-house approval with dimensional reports |
A combined note for the drawing
Where both apply, state the result and let the route follow: the tolerance, the finish and the verification. State the finish and the hatch angle, because they control how the bore wears
Applications
Honing is used for holding roundness, straightness and a controlled surface pattern in a bore, and in practice it appears most often in hydraulic cylinder bores, engine cylinders, gear bores, compressor bodies.
How it fits into a machining route
Honing is one operation in a sequence: roughing to leave even stock, any stress relieving the geometry needs, semi finishing, then the finishing operation that holds the tolerance. The order is what keeps the result stable as the machine warms up and the batch runs.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: the required geometry correction, not just the size. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is in-house approval with dimensional reports. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Air gauge and a roughness trace across the hatch is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Honing?
IT6 is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
4140 alloy steel is the usual choice, supplied against in-house approval with dimensional reports.
How is the result verified?
Air gauge and a roughness trace across the hatch, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
A bore that is not round after machining, which honing cannot economically correct.
How long does it take and what does it cost?
A realistic cycle is 5 to 20 minutes per bore, and the cost driver is the required geometry correction, not just the size.
Related capability
If you are specifying Honing on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Honing in the encyclopedia: High Speed Machining, Thread Milling, 304 Stainless Steel. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
