304 Stainless Steel FAQ: the questions buyers ask

304 Stainless Steel is the general purpose austenitic stainless steel, with chromium and nickel. It is used for general corrosion resistant parts where the chloride resistance of 316L is not needed. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.

It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, oil and gas is used as the example: materials that work harden and still have to be certified.

The questions buyers ask

What is 304 Stainless Steel used for?

It is used for general corrosion resistant parts where the chloride resistance of 316L is not needed. The general purpose austenitic stainless steel, with chromium and nickel.

What tolerance can be held?

±0.02 mm is typical, held on the features that carry the function and confirmed by standard dimensional inspection.

Which material should be specified?

304 stainless steel is the usual choice; the certificate requirement is EN 10204 3.1 available.

What finish comes as standard?

Ra 1.6 µm as machined. A finer finish is a separate operation and is quoted as one.

How long does it take?

A realistic cycle is moderate cutting speed, and the cost driver is material cost is lower than 316L.

What information is needed for a quotation?

A STEP or IGES model and a PDF drawing with tolerances, material and finish called out, plus the quantity and the expected repeat frequency.

Can the same result be guaranteed on a repeat order?

Yes, because the fixtures, tool lists and verified programmes are retained for the life of the part number.

What is the most common mistake on the drawing?

Using it in a marine or chloride environment, where it pits.

Applications

304 Stainless Steel is used for general corrosion resistant parts where the chloride resistance of 316L is not needed, and in practice it appears most often in fasteners, food preparation surfaces, architectural hardware, general brackets.

How it fits into a machining route

The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: material cost is lower than 316L. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.

Standards, documentation and what is issued

The documentation requirement is EN 10204 3.1 available. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.

Standard dimensional inspection is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.

Frequently asked questions

What tolerance should be specified for 304 Stainless Steel?

±0.02 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.

Which material is usually used?

304 stainless steel is the usual choice, supplied against EN 10204 3.1 available.

How is the result verified?

Standard dimensional inspection, with the results recorded so a repeat order can be compared with the first.

What is the most common mistake?

Welding a thick section without considering carbide precipitation.

How long does it take and what does it cost?

A realistic cycle is moderate cutting speed, and the cost driver is material cost is lower than 316L.

Related capability

If you are specifying 304 Stainless Steel on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.

Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.

Related entries

These entries sit next to 304 Stainless Steel in the encyclopedia: 6061-T6 Aluminium, 7075-T6 Aluminium, Hydraulic Manifolds. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.