A beginner's guide to Lapping
Lapping is a fine finishing process where the part is rubbed against a lap with a loose abrasive slurry. It is used for achieving extreme flatness and a very fine finish on sealing and gauging faces. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, automotive is used as the example: a fixed takt, because a late delivery stops the line.
In plain terms
Lapping is a fine finishing process where the part is rubbed against a lap with a loose abrasive slurry. If you have not met the term before, the useful way to think about it is this: it is chosen when a part needs achieving extreme flatness and a very fine finish on sealing and gauging faces.
The terms you will hear
- Flatness achievable – 0.0005 mm over 100 mm.
- Surface finish – Ra 0.025 to 0.1 µm.
- Stock removal – 0.002 to 0.01 mm.
What it costs and how long it takes
Skill and inspection time, because it cannot be hurried, and a realistic cycle is 30 to 120 minutes for a set of faces. Those two numbers, not the headline hourly rate, decide the price of the part.
What to ask a supplier
- What tolerance will you hold in production, not just on the first part?
- What does the dimensional report cover, and which standard is it written to?
- What happens to the fixtures and programmes if we reorder in a year?
Applications
Lapping is used for achieving extreme flatness and a very fine finish on sealing and gauging faces, and in practice it appears most often in seal faces, gauge blocks, valve plates, optical mounts.
How it fits into a machining route
Lapping is one operation in a sequence: roughing to leave even stock, any stress relieving the geometry needs, semi finishing, then the finishing operation that holds the tolerance. The order is what keeps the result stable as the machine warms up and the batch runs.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: skill and inspection time, because it cannot be hurried. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is in-house approval with dimensional reports. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Optical flat with a monochromatic light source is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Lapping?
±0.002 mm with flatness to 0.001 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
316L stainless steel is the usual choice, supplied against in-house approval with dimensional reports.
How is the result verified?
Optical flat with a monochromatic light source, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
Embedded abrasive left in a soft material, which later scores the mating face.
How long does it take and what does it cost?
A realistic cycle is 30 to 120 minutes for a set of faces, and the cost driver is skill and inspection time, because it cannot be hurried.
Related capability
If you are specifying Lapping on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Lapping in the encyclopedia: Wire EDM, Sinker EDM, PEEK. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
