Surface finish achievable with Duplex 2205 Stainless Steel
Duplex 2205 Stainless Steel is a two phase stainless steel with roughly equal ferrite and austenite. It is used for parts that need high strength and resistance to chloride stress corrosion. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, semiconductor is used as the example: cleanliness and surface condition that matter more than the nominal size.
What finish is achievable
The finish left by Duplex 2205 Stainless Steel is Ra 1.6 µm as machined. It is measured with a stylus instrument and reported as Ra, and the lay – the direction of the pattern – matters as much as the value on a face that seals or slides.
| Aspect | Value |
|---|---|
| Finish | Ra 1.6 µm as machined |
| Process | Duplex 2205 Stainless Steel |
| Measurement | stylus instrument or comparison sample |
| Tolerance held | ±0.02 mm |
| Effect of cost | cutting time and the cost of the material |
How it is improved
A finer finish is a separate operation, not a setting: a finishing pass, a dressing pass, or a secondary process. Cutting time and the cost of the material, so the call out belongs only on the faces that need it.
How it is checked
Dimensional inspection with a certificate review. Where the drawing gives a value, the report records where and how it was measured, because the same face can read differently in different directions.
Applications
Duplex 2205 Stainless Steel is used for parts that need high strength and resistance to chloride stress corrosion, and in practice it appears most often in offshore hardware, chemical plant, pressure vessels, pump and valve parts.
How it fits into a machining route
Duplex 2205 Stainless Steel is chosen at the drawing stage, and everything downstream follows from it: the tool geometry, the cutting data, the heat treatment and the certificate. Changing the grade later is a different part, not a different quote.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: cutting time and the cost of the material. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is EN 10204 3.1 with NORSOK where required. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Dimensional inspection with a certificate review is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Duplex 2205 Stainless Steel?
±0.02 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
duplex 2205 stainless steel is the usual choice, supplied against EN 10204 3.1 with NORSOK where required.
How is the result verified?
Dimensional inspection with a certificate review, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
Welding it without controlling the heat input, which upsets the phase balance.
How long does it take and what does it cost?
A realistic cycle is slow, with a rigid setup required, and the cost driver is cutting time and the cost of the material.
Related capability
If you are specifying Duplex 2205 Stainless Steel on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Duplex 2205 Stainless Steel in the encyclopedia: 316L Stainless Steel, 304 Stainless Steel, Splined Shafts. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
