Duplex 2205 Stainless Steel for robotics parts
Duplex 2205 Stainless Steel is a two phase stainless steel with roughly equal ferrite and austenite. It is used for parts that need high strength and resistance to chloride stress corrosion. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, robotics is used as the example: repeatability across a family of near identical parts.
What the application demands
In robotics work the requirement is repeatability across a family of near identical parts. Every axis has to assemble without shimming, which is why the specification is written the way it is.
Typical parts
- Joint housings, where tensile strength matters.
- Encoder mounts, where yield strength matters.
- Gripper fingers, where hardness matters.
How Duplex 2205 Stainless Steel fits
Duplex 2205 Stainless Steel is a two phase stainless steel with roughly equal ferrite and austenite, and in this application that is used for parts that need high strength and resistance to chloride stress corrosion. The tolerance held is ±0.01 mm, and the documentation that goes with it is in-house approval with dimensional reports.
Practical notes
Machine it with a positive cut and a rigid setup. Where the drawing and the standard disagree, the conflict is raised at quotation rather than resolved silently on the machine.
| Specification | Typical value |
|---|---|
| Tensile strength | 620 MPa |
| Yield strength | 450 MPa |
| Hardness | 230 HB |
| Density | 7.80 g/cm³ |
| Machinability | difficult: high strength and work hardening |
| Corrosion resistance | excellent, including pitting and stress corrosion |
Applications
Duplex 2205 Stainless Steel is used for parts that need high strength and resistance to chloride stress corrosion, and in practice it appears most often in offshore hardware, chemical plant, pressure vessels, pump and valve parts.
How it fits into a machining route
Duplex 2205 Stainless Steel is chosen at the drawing stage, and everything downstream follows from it: the tool geometry, the cutting data, the heat treatment and the certificate. Changing the grade later is a different part, not a different quote.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: cutting time and the cost of the material. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is EN 10204 3.1 with NORSOK where required. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Dimensional inspection with a certificate review is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Duplex 2205 Stainless Steel?
±0.02 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
duplex 2205 stainless steel is the usual choice, supplied against EN 10204 3.1 with NORSOK where required.
How is the result verified?
Dimensional inspection with a certificate review, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
Welding it without controlling the heat input, which upsets the phase balance.
How long does it take and what does it cost?
A realistic cycle is slow, with a rigid setup required, and the cost driver is cutting time and the cost of the material.
Related capability
If you are specifying Duplex 2205 Stainless Steel on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Duplex 2205 Stainless Steel in the encyclopedia: 2024-T3 Aluminium, 316L Stainless Steel, Bearing Housings. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
Previous: Wire EDM for rail parts
