6061-T6 Aluminium for aerospace parts
6061-T6 Aluminium is a heat treatable aluminium alloy with magnesium and silicon, in the T6 temper. It is used for general machined parts where weight, strength and cost have to be balanced. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, aerospace is used as the example: traceability and a first article before anything enters the batch.
What the application demands
In aerospace work the requirement is traceability and a first article before anything enters the batch. Weight targets leave no margin for oversized sections, which is why the specification is written the way it is.
Typical parts
- Structural brackets, where tensile strength matters.
- Actuator housings, where yield strength matters.
- Wing rib fittings, where hardness matters.
How 6061-T6 Aluminium fits
6061-T6 Aluminium is a heat treatable aluminium alloy with magnesium and silicon, in the T6 temper, and in this application that is used for general machined parts where weight, strength and cost have to be balanced. The tolerance held is ±0.01 mm, and the documentation that goes with it is AS9100 with full material traceability.
Practical notes
Use it as the default for any part that does not need higher strength. Where the drawing and the standard disagree, the conflict is raised at quotation rather than resolved silently on the machine.
| Specification | Typical value |
|---|---|
| Tensile strength | 310 MPa |
| Yield strength | 276 MPa |
| Hardness | 95 HB |
| Density | 2.70 g/cm³ |
| Machinability | good, with a built up edge at low speed |
| Weldability | good, with a loss of strength in the heat affected zone |
Applications
6061-T6 Aluminium is used for general machined parts where weight, strength and cost have to be balanced, and in practice it appears most often in enclosures, brackets, heat sinks, machine frames.
How it fits into a machining route
6061-T6 Aluminium is chosen at the drawing stage, and everything downstream follows from it: the tool geometry, the cutting data, the heat treatment and the certificate. Changing the grade later is a different part, not a different quote.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: material cost is low, so the process dominates. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is EN 10204 3.1 available on request. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Standard dimensional inspection is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for 6061-T6 Aluminium?
±0.02 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
6061-T6 aluminium is the usual choice, supplied against EN 10204 3.1 available on request.
How is the result verified?
Standard dimensional inspection, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
Calling up a hard anodise on a part with tight tolerances, because the coating builds up.
How long does it take and what does it cost?
A realistic cycle is fast cutting, low tool wear, and the cost driver is material cost is low, so the process dominates.
Related capability
If you are specifying 6061-T6 Aluminium on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to 6061-T6 Aluminium in the encyclopedia: 17-4PH Stainless Steel, Ti-6Al-4V Titanium, Mould Inserts. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
Previous: Deburring for rail parts
