What drives the cost of CNC Milling
CNC Milling is a cutting process where a rotating multi tooth tool removes material from a stationary workpiece. It is used for producing flat faces, pockets, slots and contoured surfaces on prismatic parts. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, robotics is used as the example: repeatability across a family of near identical parts.
The four things that move the price
- Tolerance: holding ±0.02 mm across a batch costs more than holding it once.
- Material: 6061-T6 aluminium is priced on the certificate as well as on the bar.
- Batch size: setups and first article inspection are fixed costs.
- Finishing and packing: Ra 1.6 µm as milled, and packing is specified by the part.
Why the same part is quoted differently
Because the route is not the same. Machine time and the number of setups, so two quotations can differ by a third without either being wrong. Asking what route has been assumed is the fastest way to compare them.
How to reduce it
- Use the largest corner radius the design allows, because it permits a bigger step over.
- Open internal corners with a small relief so a standard cutter fits.
| Item | Note |
|---|---|
| Cost driver | machine time and the number of setups |
| Cycle | 10 to 60 minutes per part |
| Tolerance | ±0.02 mm |
| Material | 6061-T6 aluminium |
| Documentation | in-house approval with dimensional reports |
Applications
CNC Milling is used for producing flat faces, pockets, slots and contoured surfaces on prismatic parts, and in practice it appears most often in enclosures, brackets, mould plates, machine frames.
How it fits into a machining route
CNC Milling is one operation in a sequence: roughing to leave even stock, any stress relieving the geometry needs, semi finishing, then the finishing operation that holds the tolerance. The order is what keeps the result stable as the machine warms up and the batch runs.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: machine time and the number of setups. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is in-house approval with dimensional reports. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
CMM, height gauge and roughness gauge is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for CNC Milling?
±0.02 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
6061-T6 aluminium is the usual choice, supplied against in-house approval with dimensional reports.
How is the result verified?
CMM, height gauge and roughness gauge, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
Climb milling used on a machine with backlash, which shows as a step on the wall.
How long does it take and what does it cost?
A realistic cycle is 10 to 60 minutes per part, and the cost driver is machine time and the number of setups.
Related capability
If you are specifying CNC Milling on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to CNC Milling in the encyclopedia: Wire EDM, Sinker EDM, 316L Stainless Steel. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
