How to specify Hydraulic Manifolds on a drawing
Hydraulic Manifolds is a block with drilled and ported passages that connects valves, pumps and actuators. It is used for replacing pipework with a single machined block, in mobile and industrial hydraulics. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, robotics is used as the example: repeatability across a family of near identical parts.
What belongs on the drawing
A clear drawing for Hydraulic Manifolds states the function, the tolerance and the verification, and leaves the route open where the function allows it.
- The feature and its tolerance: ±0.05 mm on port position, applied to the features that locate the part.
- The material and its condition: 6082-T6 aluminium or S355 steel, with the certificate requirement.
- The surface finish: Ra 3.2 µm in the passages, called out only where it does something.
- The verification: pressure test certificate with a dimensional report, and the standard the report is written to.
Mistakes that cost money
- An intersecting passage that leaves a burr at the junction, which makes the part more expensive without making it better.
- A plug that is not sealed, so the circuit leaks internally, which makes the part more expensive without making it better.
A workable note
Where a general note is used, say so once in the title block and keep the feature level call outs for the dimensions that matter. State the cleanliness requirement and the test pressure
Applications
Hydraulic Manifolds is used for replacing pipework with a single machined block, in mobile and industrial hydraulics, and in practice it appears most often in mobile machinery, presses, test rigs, marine hydraulics.
How it fits into a machining route
Hydraulic Manifolds is produced by whichever route reaches it most reliably, and it is usually the reason the rest of the part is dimensioned the way it is. Datums are chosen so that this feature is measured from what it actually has to be square or concentric with.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: deep hole drilling and the pressure test. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is pressure test certificate with a dimensional report. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Port gauge and a pressure test rig is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Hydraulic Manifolds?
±0.05 mm on port position is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
6082-T6 aluminium or S355 steel is the usual choice, supplied against pressure test certificate with a dimensional report.
How is the result verified?
Port gauge and a pressure test rig, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
A plug that is not sealed, so the circuit leaks internally.
How long does it take and what does it cost?
A realistic cycle is 2 to 8 hours for a block, and the cost driver is deep hole drilling and the pressure test.
Related capability
If you are specifying Hydraulic Manifolds on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Hydraulic Manifolds in the encyclopedia: O-Ring Grooves, Bearing Housings, EN 10204 Material Certificates. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
