Materials and Wire EDM: what works and what does not
Wire EDM is a spark erosion process that cuts a profile with a thin travelling wire in deionised water. It is used for cutting hardened material, sharp internal corners and parts with no cutting force. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, oil and gas is used as the example: materials that work harden and still have to be certified.
What works with it
The material and the process are chosen together. For work involving Wire EDM the usual choice is D2 tool steel, for the reason that cutting area and the number of skim passes.
- %s – the default, because it balances cost, availability and machinability.
- Stainless grades – chosen where corrosion resistance or cleaning rules decide the material.
- Aluminium grades – chosen where weight or thermal conductivity matters more than strength.
- Engineering plastics – chosen where insulation, weight or chemical resistance is the point.
What to watch
Material behaviour changes the process before it changes the drawing. A grade that work hardens needs a different tool geometry and a different feed, and a certificate requirement such as in-house approval with dimensional reports has to be on the order before the bar is cut.
| Specification | Typical value |
|---|---|
| Typical tolerance | ±0.005 mm, ±0.002 mm with skim passes |
| Surface finish | Ra 0.2 to 1.6 µm |
| Kerf | 0.25 to 0.35 mm |
| Cutting speed | up to 300 mm²/min roughing, less for fine finishes |
| Taper | up to 30 degrees per 100 mm |
| Material requirement | electrically conductive |
Applications
Wire EDM is used for cutting hardened material, sharp internal corners and parts with no cutting force, and in practice it appears most often in punch and die work, hardened gauges, prototype laminations, medical cutting tools.
How it fits into a machining route
Wire EDM is one operation in a sequence: roughing to leave even stock, any stress relieving the geometry needs, semi finishing, then the finishing operation that holds the tolerance. The order is what keeps the result stable as the machine warms up and the batch runs.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: cutting area and the number of skim passes. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is in-house approval with dimensional reports. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Optical comparator and surface roughness gauge is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Wire EDM?
±0.005 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
D2 tool steel is the usual choice, supplied against in-house approval with dimensional reports.
How is the result verified?
Optical comparator and surface roughness gauge, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
Assuming a sharp internal corner is free: the wire has a radius.
How long does it take and what does it cost?
A realistic cycle is 1 to 8 hours depending on height, and the cost driver is cutting area and the number of skim passes.
Related capability
If you are specifying Wire EDM on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Wire EDM in the encyclopedia: Deep Hole Drilling, Reaming and Boring, C3604 Brass. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
