High Speed Machining tolerances: what is realistic and what it costs
High Speed Machining is milling at high spindle speed with light radial engagement and high feed per tooth. It is used for removing metal quickly from thin walled or difficult parts with low cutting force. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, automotive is used as the example: a fixed takt, because a late delivery stops the line.
What is realistic
The tolerance that can be held on High Speed Machining depends on the feature, the material and the batch size. A value held once on a first article is not the same as a value held across a thousand pieces.
| Aspect | Typical value |
|---|---|
| Process tolerance | ±0.01 mm |
| Measurement | CMM and roughness gauge |
| Surface finish | Ra 0.8 µm achievable |
| Batch effect | capability, not a single measurement |
| Documentation | AS9100 where the customer requires it |
| Cost effect | machine hour cost, because the spindle is expensive to run |
What it costs to hold
Tolerance and cost are not proportional; they are closer to exponential once a process has to be controlled rather than simply performed. Machine hour cost, because the spindle is expensive to run, which is why the drawing should say which features carry the function and which do not.
How it is verified
CMM and roughness gauge. Calibration dates and measurement uncertainty are recorded with the result, so a later order can be compared with the first instead of being measured from scratch.
Applications
High Speed Machining is used for removing metal quickly from thin walled or difficult parts with low cutting force, and in practice it appears most often in thin walled enclosures, aluminium aerospace parts, mould finishing, graphite electrodes.
How it fits into a machining route
High Speed Machining is one operation in a sequence: roughing to leave even stock, any stress relieving the geometry needs, semi finishing, then the finishing operation that holds the tolerance. The order is what keeps the result stable as the machine warms up and the batch runs.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: machine hour cost, because the spindle is expensive to run. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is AS9100 where the customer requires it. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
CMM and roughness gauge is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for High Speed Machining?
±0.01 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
7075-T6 aluminium is the usual choice, supplied against AS9100 where the customer requires it.
How is the result verified?
CMM and roughness gauge, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
A toolpath with sharp direction changes, which the control cannot feed through smoothly.
How long does it take and what does it cost?
A realistic cycle is 20 to 90 minutes for a complex part, and the cost driver is machine hour cost, because the spindle is expensive to run.
Related capability
If you are specifying High Speed Machining on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to High Speed Machining in the encyclopedia: Deep Hole Drilling, Reaming and Boring, 6061-T6 Aluminium. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
