Surface Grinding Machine specifications: what the numbers mean
Surface Grinding Machine is a machine that finishes flat faces with a rotating abrasive wheel and a reciprocating table. It is used for holding flatness and parallelism on faces that seal or locate. This entry explains what it is, what the numbers on a data sheet mean, and what to put on a drawing.
It is written from the point of view of the buyer and the drawing office: the values that are realistic in production, the ones that cost money, and the way the result is verified. Where an industry sets the requirement, oil and gas is used as the example: materials that work harden and still have to be certified.
What the numbers mean
A data sheet for Surface Grinding Machine is only useful if the numbers are read against the job. The usual entries, and what they tell you, are these.
- Table size – 600 x 300 mm.
- Wheel size – 300 x 40 mm.
- Spindle power – 3 to 7 kW.
- Down feed resolution – 0.001 mm.
- Flatness achievable – 0.005 mm over 300 mm.
- Surface finish – Ra 0.2 to 0.8 µm.
Comparing offers
Two suppliers can quote the same table size and mean different things, because the figures are often quoted under the most favourable conditions. Ask what the value is measured over, what the material was, and whether it is a typical or a guaranteed figure.
| Specification | Typical value |
|---|---|
| Table size | 600 x 300 mm |
| Wheel size | 300 x 40 mm |
| Spindle power | 3 to 7 kW |
| Down feed resolution | 0.001 mm |
| Flatness achievable | 0.005 mm over 300 mm |
| Surface finish | Ra 0.2 to 0.8 µm |
What to check before specifying
Make sure the value you need is the value you have called up. Leave 0.2 to 0.4 mm for grinding, not 1 mm, and the difference between a typical and a worst case figure is where most disputes start.
Applications
Surface Grinding Machine is used for holding flatness and parallelism on faces that seal or locate, and in practice it appears most often in die and mould plates, machine slides, seal faces, gauge blocks and spacers.
How it fits into a machining route
Surface Grinding Machine is one station in a route rather than the whole of it. The part arrives with the previous operation finished and leaves with the features it is responsible for completed, so the datum and the clamping method are agreed before the first part rather than discovered on it.The route is fixed before the first part is cut, and it is the route rather than the individual setting that holds the result: stock removal allowance left by the previous operation. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Standards, documentation and what is issued
The documentation requirement is in-house approval with dimensional reports. Material is supplied against a certificate where the application calls for it, inspection results are recorded with the job, and the records are kept so that a repeat order can be compared with the first instead of being measured from scratch.
Surface plate with a dial indicator, and a roughness gauge is the verification step. Where a customer format or a standard report is required, it is agreed before the batch starts, because a report written after the event is a report nobody can use.
Frequently asked questions
What tolerance should be specified for Surface Grinding Machine?
±0.005 mm is realistic in production. Tightening it beyond the functional requirement increases cost without improving the part.
Which material is usually used?
4140 alloy steel is the usual choice, supplied against in-house approval with dimensional reports.
How is the result verified?
Surface plate with a dial indicator, and a roughness gauge, with the results recorded so a repeat order can be compared with the first.
What is the most common mistake?
The magnetic chuck holding a part that is not flat to start with.
How long does it take and what does it cost?
A realistic cycle is 30 to 120 minutes for a plate, and the cost driver is stock removal allowance left by the previous operation.
Related capability
If you are specifying Surface Grinding Machine on a drawing and want a second opinion on the route, send the model and the quantity. The first response is a manufacturability review with the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
Machining, inspection and documentation are handled in one place, which is why the dimensional report and the material certificate arrive with the parts rather than after them.
Related entries
These entries sit next to Surface Grinding Machine in the encyclopedia: Vertical Machining Centre, Horizontal Machining Centre, Sinker EDM. Reading them together gives a fuller picture of how the process, the material and the measurement affect each other.
