Tight Tolerance Programme for Consumer Electronics Enclosures
A tight tolerance programme is not a quotation for a part number. It is an agreement about how enclosures will be made, measured and released every time they are ordered. This page sets out what that looks like for enclosures in C110 copper, where the difficulty is visible surfaces that have to be flawless on the first shipment.
The work described here runs in a route with grinding and jig boring support alongside machining for Consumer Electronics customers. A launch date that does not move, and parts judged on appearance as much as on dimension. The route below is the one we would propose on a first enquiry, and it is the one we would still be running two years later.
What this programme has to deliver
These are the four things that decide whether a tight tolerance programme works in practice. Everything else is detail that gets settled at the quotation stage.
- Dimensions held to ±0.02 mm on the features that locate the part, not just on the ones that are easy to measure.
- Material supplied against a certificate, because cosmetic surface standards agreed with the brand applies to this work.
- Repeatability between batches, so the hundredth part assembles like the first.
- Documentation that arrives with the parts rather than two weeks after they do.
Process route
The route is finish machining after stress relieving, with temperature controlled measurement. Operation order is fixed before the first part is cut: roughing to leave even stock, stress relieving where the geometry needs it, semi finishing, then the finishing operations that hold ±0.02 mm. That order is what keeps the tolerance stable as the machine warms up and the batch runs.
| Programme | Tight Tolerance Programme |
|---|---|
| Typical parts | enclosures |
| Material | C110 copper |
| Tolerance | ±0.02 mm on locating features |
| Batch size | 10 to 500 pieces |
| First parts | 10 to 15 working days |
| Equipment | a route with grinding and jig boring support alongside machining |
| Documentation | cosmetic surface standards agreed with the brand |
The advantage of running it this way is that the tolerance is held by the process, not by selection at inspection. Where a drawing calls for something the route cannot hold economically, that is raised at quotation rather than after the parts are made.
Materials, tolerances and finishes
C110 copper is purchased against a certificate and checked on receipt, so the composition is known before any cutting starts. Where the application calls for a different grade, the change is quoted with the machining implications spelled out rather than absorbed silently.
±0.02 mm is held on the features that matter and left open elsewhere, because a tolerance that costs money without adding function is a cost the drawing should not carry. Surface finish, edge breaks and protective treatments are specified on the drawing and confirmed before packing.
Typical parts in this programme
The part numbers that come through this route tend to look alike in the way that matters: they are parts judged on appearance as much as on dimension. A representative list for Consumer Electronics work looks like this.
- Enclosures in C110 copper, machined complete in as few setups as the geometry allows.
- Heat sinks where the tolerance stack up is carried by the machining rather than by the assembly.
- Connector shells that repeat on a known cycle, usually released against a schedule rather than one order at a time.
- Revision work on the same family, where a drawing change has to be absorbed without a new fixture.
In each case the quotation is built on the route rather than on a single part number, which is why the price holds when the batch is repeated and the design moves on.
What drives the cost
Four things move the number, and they are worth separating because they are usually confused with each other. Tolerance is the first: holding ±0.02 mm across a batch costs more than holding it once, because it has to be measured and because the tooling has to be managed. Material is the second, and C110 copper is priced on the certificate as well as on the bar.
Batch size is the third. Setups and first article inspection are fixed costs, so 10 to 500 pieces spreads them differently depending on how the order is released. Surface treatment and packing are the fourth, and they are quoted separately so that a change of finish does not force a re-quote of the machining.
Quality assurance and documentation
Critical features are measured on calibrated equipment in a controlled room and the results are filed with the job, so a repeat order can be compared with the first instead of being measured from scratch.
Cosmetic surface standards agreed with the brand. Calibration dates and measurement uncertainty are recorded with every result, and first article reports are issued where the application requires them.
How a programme starts
Three steps, and none of them commit anyone to a production order. First, the drawing and model are reviewed for manufacturability, and anything that adds cost without adding function is pointed out at that stage. Second, a quotation is issued with the route, the batch assumption and the lead time written into it.
Third, the first parts are made, measured and reported. That report is the basis for release: if the dimensions and the documentation are accepted, the route is fixed and the programme runs on a schedule. If something needs changing, it is changed before the batch starts rather than during it.
Programme timing, capacity and logistics
First parts are quoted at 10 to 15 working days and production runs at 10 to 500 pieces. Capacity is held against a schedule rather than promised in the abstract, and call off quantities are agreed so that material is available when the order releases.
Packaging is specified by the part: individual protection for finished surfaces, separation for assemblies, and export crating with a packing list. Shipments leave with the documentation that matches the order.
Frequently asked questions
What do you need to quote enclosures?
STEP or IGES for the model and a PDF drawing with tolerances, material and finish called out. Quantity and expected repeat frequency matter as much as the geometry, because they decide the route.
Can you hold ±0.02 mm in production, not just on the first article?
Yes. It is held by the process route and tool compensation rather than by sorting at inspection, which is why the operation order and the fixture are settled before the batch starts.
How is documentation handled?
Cosmetic surface standards agreed with the brand is issued with the shipment where the application requires it, and the records are kept with the job so that a later order can be traced back to the material batch and the measurement equipment used.
Can you work to our drawings and our standards?
Yes. Most of this work is made to customer drawings under the customer's own quality requirements. Where a standard conflicts with the drawing, the conflict is raised before quotation rather than resolved silently on the machine.
What happens if the drawing is still changing?
That is what the tight tolerance programme is for. Changes are quoted on the delta rather than on a fresh part number, and the revision history is kept with the job.
Getting started
Send the drawing and the expected quantities. The first response is a manufacturability review with the route, the likely risk points and a quotation, so the decision can be made on facts rather than on a price alone.
